Mold Design Quote
 Bid Specification Sheet

Information for mold design bids can be sent to Advanced 3D
Design online 24 hours a day by filling out and submitting the
following form. Leave the items blank that do not apply to
your mold quote request or that you do not have at this time.
Filling in the RFQ form below does not constitute a contract between
you and us. This preliminary information is for quoting purposes.
We will treat your information with the strictest confidentiality!

Company Name:

Contact Name:

Company Address:

City: Country: Phone: E-Mail:

State/Province: Postal Code: Fax: Web Site Address:

 Deliver the mold design quote by:
Mail E-Mail Fax Phone
FTP Web Cam Video Conference

  Mold Quote must be received by:
 
  Urgent   Normal Timing

 Plastic Part Data

Part Name: Molding Resin: Filler:

Part Number & Revision: Resin Supplier: Shrinkage Rate:

Mold Quote - Design Data

Number of Cavities: Mold Size (lg x wd x hgt): Exact Size Approx. Size Maximum Size Gate Type: Sub Gate Tab Gate Edge Gate Pin Point Diaphragm Valve Gate Center Sprue Runner Type: Round Trapezoidal Hot Runner Supplier (if standard requirement): Low Voltage High Voltage Mold Type: A B X AX T M.U.D. Family Hot Drop Hot Runner Over Molding Mold Base Cat. No. (if standard): "O"=  "R"=  "D"=  "C"=  "S"=  "M"=  Mold Base Steel Type/Number: Pocket Type: Blind Window Ejector Type: Pins Sleeves Blades Strippers Lifters Unscrewing

 Special Mold Actions:

Reverse Injection Gas Assist Rack Driven Tri-Plate Pull Rod Drive Tri-Plate Latch Driven Tri-Plate 2 Stage Injection "Bermer" Ejector Return Stripper Plate Ejector Parting Line Locators 2 Stage Ejector Inject/Eject Stack Mold Front Half Cam Action Internal Lifters Buried Core Pull

Spring Loaded Ejector Stripper Ring Ejector Latch Driven Ejector Accelerated Ejector Early Ejector Return Air Assisted /Poppet Ejector Front Ejection Guided Ejection Mechanical Core Pull Hydraulic Core Pull Spring Load Core Pull Rack Drive Unscrew Spline Drive Unscrew Motor Drive Unscrew

 Mold Features:

Flush style K.O. extensions Runner shut-off(s) Pry slots between plates Steel type and hardness stamped on mold parts Tapped thermocouple well Pressure sensor with wire slots and plug 2 piece cams - body and face Cam wear plates required Wire slots required Insulation board on clamp plates Grease grooved bushings Spare parts/inserts required Mold straps required Engraving Inserts Date Inserts /Clock Recycle Medallion

 Heating and Cooling Requirements:

Tap's for water lines Metric NPT
Hot Oil Fittings #	Jiffy Plugs #
Rotating Union Spiral Cooling Cores Thermal Pins Gas Charged Cores Bubbler Tubes Logic Seal Cooling H2O Manifold Req'd Cascade Junction	Straight Blade Baffles Spiral Blade Baffles Cooling in Main Cavity Cooling in Main Core Water in Mold Plates Water in Retainer Plates Tubular Heaters Heater Cartridges

 Cavity, Core and Insert Information :
 (only fill in data that applies to your parts)

Cavity Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /Cav I.D.:        Sub Insert /Laminate Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving / I.D. : Stripper Ring /Insert Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /I.D. :

Core Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /Core I.D.:       Slide Face Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /I.D.: Lifter Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /I.D. :

Slide Body Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /I.D. : Gate Insert Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /I.D. : Other Insert: Material Type: Hdn's /Heat Treat: Plating /Coating: Finish SPI/SPE#: Texture on Molding: Engraving /I.D. :

 Design Specifications:

Customer Specifications Supplied SPI Specifications Supplied ProMold Specifications Supplied NTMA Specifications Supplied  Type of Mold Design Required: Detailed Layout  Type of Drawing Title Blocks Required: Customer Supplied Advanced 3D

Check the Type of File(s) Furnished

.IGS iges .DXF or .DWG Autocad .PRT Unigraphics .STL .X_T or .X_B parasolid .PAR .PSM .ASM .DFT Solid Edge .STP step .WRL .WMF Windows Metafile Other file type(s) (specify)

 Molding Machine Data:

Press Manufacturer:	Clamp Tonnage:
K. O. Pattern:	SPI Standard
K.O Thread Size:	Ejector Stroke Dist:
Tie Bar Locations:	Tie Bar Diameters:
Min. Mold Height:	Max. Mold Height:
Core Pull Sequence      Equipped	Max. Open Daylight:
Integrated Hot     Runner Controls

Enter any other requirements or instructions  here for your design mold quote:

  

If you have drawing data, sketches or files that should be reviewed as
part of this bid request, you can attach them to an E-mail sent to us.
Please refer to our list of compatible files that we can accept from you.
Also, you may use our FTP SITE to upload your larger files (total bigger
than 4 Megabytes) or if there are more than a few of them.

Thank You for your time in supplying this information. We do understand
that this is a considerable amount of information requested, however,
we will be able to give you an accurate, fair and complete quote. If you
are unfamiliar or unable to furnish all the data above, leave it blank
and we will be happy to assist and recommend the mold design features
and parameters that can give you the best possible mold design at the
least cost. Please note the mold quote will be for 2 sets of drawings unless
otherwise specified. We will be responding to your mold design quote
request shortly and Thank You again.